 |
 |
|||||||||||||||||||||||||||||||||
The
CORE snap™ banner is a high quality,
compact, single-sided roll-up banner with a great modern design. Graphics for the CORE snap™ banner are inter-changable, just open the lid, change the graphic and ‘snap’ the lid back down - so when your message changes the banner doesn’t have to! CORE snap™ banners have adjustable feet, are supplied in padded bags and are available in 3 different sizes; the mini 600mm, 850mm, and 1000mm. |
||||||||||||||||||||||||||||||||||
 |
||||||||||||||||||||||||||||||||||
Grip-Rails are
available for use
with textile prints
or those that do
not bond with
adhesives. |
Optional
Adjustable Poles
allow you to adjust
your graphic to
whatever height
you want. |
Low-Voltage
Spotlights clip
to the pole
and illuminate
your graphic for
maximum impact. |
CORE snap™
banners are covered by a 5-Year Guarantee against component failure
for maximum peace of mind.
|
|||||||||||||||||||||||||||||||
 |
||||||||||||||||||||||||||||||||||
 |
||||||||||||||||||||||||||||||||||
 |
Slimline design |
 |
Stabilising foot |
 |
Easy access to prints |
 |
Slide-in graphics |
 |
Adjustable feet |
 |
||||||||||||||||||||||||
|
Standard 3-part poles give you
a large image area, but optional
adjustable poles allow you to
display your graphic at any height
from 850mm to 2150mm.
CORE snap™ banners have no parts protruding from the front of the banner, as the support is provided from the stabilising foot at the rear. |
||||||||||||||||||||||||||||||||||
It is quite simple to install graphics into the banner
following these simple instructions. In order to replace
graphics simply carry out these steps in reverse order
to remove the original graphic. It is therefore very important that you KEEP THE LOCKING PIN in the pocket
found in the lid of the padded bag, as this will be needed to lock the tension in the Internal Roller before opening
the base. For best results ensure graphic panel media does not exceed 300 MICRONS in total thickness. |
||||||||||||||||||||||||||||||||||
 |
||||||||||||||||||||||||||||||||||
 |
Step 1: Affix Panel
Strips to the back
of the panel at the
top and bottom
with the red and
yellow tapes
ensuring panel
remains straight. |
 |
Step 2: Slide the
Banner Rail along
the Panel Strip
at the top of the
panel as shown.
Secure the Banner
Rail with tape if
desired. |
 |
Alternatively if
using Grip Rails:
Simply open the
profile and slide
top of the graphic
in as shown. Press
down hard to close
the profile. |
 |
Step 3:
Undo the
allen key screws
at each end of
the banner to
open the lid and
carefully remove
the Internal Roller
from the base. |
 |
Step 4: Slide Internal Roller onto bottom of the graphic. Return roller into base ensuring indented section is facing upwards. |
 |
Alternatively
if using Grip
Roller: Open Grip
Roller profi le and
slide graphic in as
shown. Press down
hard to close the
profi le. |
 |
Step 5: Close the
lid and tighten the
allen key screws
before pulling out
the locking pin.
Allow the graphic
to gently retract
into the base. |
 |
||||||||||||||||||||
 |
||||||||||||||||||||||||||||||||||
 |
||||||||||||||||||||||||||||||||||
 |
||||||||||||||||||||||||||||||||||
 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Copyright ©2007 CORE Display Systems Ltd.